德国乐力士LELUX空呼潜水充气泵

225/330bar, 100 l/min
Model  LELUX100型号


Technical Data for Compressor Block:
压缩机主机技术参数：

Medium :
压缩介质	Air
Intake Temperature :
进气温度	+5 to +45°C
Ambient Temperature :
环境温度	+5 to +45°C
Nominal Pressure max. :
公称压力	330 bar adjusted by safety valve
Working Pressure :
工作压力	225/330 bar  (Choice one pressure)
Capacity :
流量	100 l/min
Speed :
转速	2300 1/min
Number of Compression stages :
压缩级数	3
Number of Cylinders :
汽缸数	3
Power consumption at max. pressure
较大压力时的功率消耗	2.2 kW
Drive :
驱动方式	V-Belt
 






Technical Data for Prime Mover:
驱动电机的技术参数：
Type :
型号	three phase electric motor
Power :
功率	2.2 kW
Speed :
转速	1450 1/min
Enclosure :
防护等级	IP55
Voltage:
电压	200-240V
Frequency :
频率	60 Hz


Standard Scope of Supply:

COMPRESSORBLOCK 
压缩机主机

Oil pump for forced-feed lubrication with oil filter
油泵带油滤器作注油式润滑
Oil sump content: For blocks  i100.x:0.36
油池容量：主机I100x: 0.36升；
Micronic intake filter
进气滤芯
Interstage coolers, air cooled after each stage
每级压缩后都设有冷却器
Aftercooler, air cooled, outlet temp. approx. 10-15 °C above ambient temp.
压缩气体经过冷却器后的温度大约**环境温度10-15 °C
Intermediate oil/water separators after each stage
每级压缩后都设有中级水油分离器
Final oil/water separator
终级水油分离器
Safety valves after each stage
每级压缩后都设有安全阀
Final pressure safety valve
终级安全阀
Pressure maintaining and check valve before compressor outlet
压缩机出口前设有压力维持阀及单向阀
First oil filling with final test
压缩机已加注润滑油并经过整机运行测试
Oil change 2000 hours or 2 years whichever comes first
润滑油更换时间为运行2000小时或两年（二者以先到为准）





LELUX air quality is better than the most stringent standards DIN EN 12021:

 乐力士空气质量优于较严格的DIN EN 12021标准：

	LELUX standard指标	DIN EN 12021  standard 标准
油分Oil	＜0.1mg/m³ 	＜0.5mg/m³ 
一氧化碳CO	＜5ppm 	＜15ppm 
水分Water	＜10mg/m³ 	＜25mg/m³ 


-P21 filter system:
-P21过滤系统:
Purification system by TRIPLEX, TRIPLEX long filter, pressure retaining valve / non-return valve and the end relief valve.
由TRIPLEX净化系统，TRIPLEX长效滤芯，保压阀/单向阀和终级安全阀组成。
-330bar inflatable device
-225/330bar 充气装置
LELUX 200/250/300 with 1 charging connector
LELUX 200/250/300带有1个充气接头 
Each charging connector includes: 1 root 1 meters long filling pipe
1 with the emptying function of pneumatic valve, pneumatic bottle joint is 5/8 BSP, DIN EN144-2        1 pressure gauges
每个充气接头包括： 	1根1米长充气管
                       	      1个带有放空功能的充气阀，充气瓶接头是5/8 BSP, DIN EN 144-2
                      	       1个压力表